OutdoorRouter XYZ Knowledge BaseOutdoorRouter XYZ Knowledge Base
  • Mobile
  • Wi-Fi
  • Firmware
  • Hardware
  • Development
  • Shop
  • Mobile
  • Wi-Fi
  • Firmware
  • Hardware
  • Development
  • Shop
home/Knowledge Base/Mobile Modem/Canada APN Settings for Bell

Canada APN Settings for Bell

11 views 0 March 8, 2023

For some remote areas, The Canadian carrier Bell can only support the traditional PPP protocol, please follow the steps below to switch the protocol.

Firstly, Connect a phone or computer to the 4G router via Wi-Fi or Ethernet, then log in to the router. The default router IP addresses are as below. The default password is root.

EZR23/EZR24 Indoor 4G Router
http://192.168.20.1

EZR33L/EZR34 Outdoor 4G Router
http://192.168.30.1

Login

After logging into the router admin, go to “Network > Interfaces“. Click the “Edit” button on the row of “Mobile“.

Edit 4G Router Mobile Interfaces

Under the tab of “General Setup“, choose “4G-PPP” on the option of “Protocol“.

It will show ask you to confirm “Really switch protocol?”.
Click the button “Switch protocol”.

4 0 Mobile Protocol Switch Protocol

Then it will jump to the 4G-PPP protocol set-up page. 

The modem device and service type are different from the default MobileData protocol. Please refer to the below parameters to configure the 4G-PPP protocol for Bell SIM cards.

Make sure to use the /dev/ttyUSB2 on the Modem device.

EZR23 and EZR33L choose the SIM card slot under “Active SIM Card”. If using the SIM1 slot, click the tab of “Primary SIM1”. 

EZR24 and EZR34 routers only support one sim card by default, so there has no sim card selection options, please just go ahead to input the APN.

ttyUSB2 Modem Device and SIM Card for EE 4G Router

Service type: UMTS/GPRS
APN: pda.bell.ca
PIN: Leave it empty if you have not changed the default PIN code.
PAP/CHAP username: <leave in blank>
PAP/CHAP password: <leave in blank>
Dial number: <leave in blank>

Click the “Save & Apply” button on the bottom right corner to apply the new settings. It will jump back to the interface overview page.

Bell APN Settings under PPP Protocol

Finally, unplug the power and reboot the router to activate the new settings.

After successfully connecting to Bell mobile networks, the Mobile interface will show the IPv4 address on the interface overview page.

BTW, the home page will not be updated under the 4G-PPP protocol since it is under the control of MobileData.

Tags:Bell APNAPN Settings

Was this helpful?

Yes  No
Related Articles
  • Verizon APN Address Settings
  • PPP Protocol Settings for FirstNet
  • How to Test 4G Router Network?
  • Router IMEI Number
  • APN Settings for Vodafone
  • EE APN Settings

Didn't find your answer? Contact Us

Leave A Comment Cancel reply

Knowledge Bases
  • Mobile Modem
  • Wi-Fi Hotspot
  • Custom Firmware
  • Network Hardware
  • Development
Popular Articles
  • Canada APN Settings for Bell
  • WiFi Output Power Settings
  • Supporting Legacy Wi-Fi Devices
  • Adjust the Wi-Fi Output Power
  • Collect System Log and Error Message

  Verizon APN Address Settings

Supports
  • Mobile Modem
  • Wi-Fi Hotspot
  • Custom Firmware
  • Network Hardware
Outdoor Router
  • Outdoor 4G Router
  • Indoor 4G Router
  • Outdoor Wi-Fi Extender
  • High-gain 4G Antenna
Information
  • About Us
  • Case Studies
  • Shipping Service
  • Contacts
User’s Manual
  • EZR33 Outdoor Router
  • EZR34 Outdoor Router
  • EZR23 Indoor Router
  • EZR24 CAT12 Modem
  • © 2023 OutdoorRouter. All Rights Reserved.